SMI5 SELECTOR: AMAZINGLY MINIATURE, UNBELIEVABLY RICH OF FEATURES

SMI5 SELECTOR: AMAZINGLY MINIATURE, UNBELIEVABLY RICH OF FEATURES de Lika Electronic

Par: Lika Electronic  05/02/2013
Mots-clés : Capteurs, Encodeur, Codeurs

When it comes to your speed & position feedback requirements for linear motors, pick & place robots and electronics & semiconductors manufacturing systems, SMI5 Selector sensor is the right choice. Don't be fooled by its miniature size, it is designed to offer much more than what you could expect! SMI5 Selector is the newest addition to Lika's range of incremental linear sensors. It encompasses a unique 25 x 8.5 x 15 mm (0.98 x 0.33 x 0.59”) sensor head (it is as small as a 5 cent EURO or USD coin) protected by a rugged metal housing and is able to handle extreme shock and vibration impacts as well as large temperature fluctuations (operating temperature range is between -25°C +85°C, -13°F +185°F). The dust-tight and waterproof design is IP68-rated thus it is fully resistant to oil, grease, immersion in water and common chemical contaminants. SMI5 Selector uses an advanced dual element magneto-resistive sensor for producing impressive accuracy even at highest speeds, low modulation rates and superb signal output clarity. It provides liberal mounting tolerances and enables a gap between the sensor and the magnetic substrate of up to 2 mm (0.079”) allowing for unparalleled ease of installation, while still maintaining dependable operation and high performance characteristics. The advanced conversion circuitry is fitted in the encapsulated connector and features automatic gain control (AGC) and automatic offset correction (AOC) functions for improved signal quality, minimization of the sub-divisional error (SDE) and negligible hysteresis. The non-contact magnetic technology also provides virtually wear & maintenance-free operation, eliminates interference from machine vibrations, delivers insulation protection against damages caused by eddy currents and prevents the mechanical loadings from being transmitted to the sensing system. These features ensure unparalleled reliability over time and longer operating life. The sensor generates square wave output signals and additional complementary signals (ABI, /ABI) and is offered in standard industry either Push-Pull (HTL) 10-30VDC or Line-Driver (TTL) 5VDC / 10-30VDC output circuits. As its name implies, the resolutions is selectable in the range 5 to 50 µm through the rotary selection switch provided in the connector housing; in this way it can suit the specific needs of almost any application. The maximum mechanical speed is up to 16 m/s – 52,49 ft/s. SMI5 Selector is further equipped with two integral diagnostic LEDs to signal errors. SMI5 Selector is offered along with twin SMI2 Selector model featuring selectable resolutions from 2 to 20 µm. Selector series sensors can be mounted on linear scales (MT series in both 2-mm and 5-mm pole lengths) and magnetic rings (MRI series in both 2-mm and 5-mm pole lengths) to easily fit linear and rotary applications, according to needs. Polymer/ferrite composite magnetically encoded scales can be easily applied / removed via a pre-applied self-adhesive backing while magnetic rings are available with 31 to 284-mm outer diameter (shaft diameter on request). Scales and rings are both highly immune to dirt and external contaminants. Lika’s sensors incorporate high-flex cabling specifically suited for use in cable track applications.

Mots-clés : Capteur incrémental, Capteurs, Codeur incrémental magnétique, Codeur Linéaire, Codeur magnétique, Codeurs, Codeurs Linéaires, Encodeur, Encodeurs, Push-Pull, Système de mesure magnétique, Transducteur digital,

Autres produits et services de Lika Electronic

Aperçu Encoders for Industrial Robots, Motors and OEM applications de Lika Electronic
05/12/2016

Encoders for Industrial Robots, Motors and OEM applications

At latest SPS IPC Drives exhibition in Nuremberg Lika Electronic especially focused on the range of encoders designed to be integrated into robotic systems as well as into motors and OEM applications. They are compact and modular and tailored to exactly meet the specific needs of the individual automation processes.


Aperçu Heavy-duty encoders for shipbuilding industry de Lika Electronic
21/10/2016

Heavy-duty encoders for shipbuilding industry

Encoders for shipbuilding industry, marine installations and offshore facilities are born out of Lika's long-standing, solid experience in the field. They are designed to cope with extreme and high aggressive environmental conditions. Stainless steel enclosures and special surface treatments and sealings ensure safe protection against salt water and corrosion. They are rugged and can withstand heavy mechanical stresses, shocks and vibrations and large temperature fluctuations up to -40°C +100°C


Aperçu ATEX certified encoders de Lika Electronic
21/10/2016

ATEX certified encoders

Lika Electronic has developed a comprehensive range of ATEX certified encoders: XC77 series, XAC77 series and XAC80 series. They are designed to cover a wide variety of critical applications in hazardous and harsh areas “in which explosive atmospheres caused by gases, vapours, mists or air/dust mixtures are likely to occur occasionally” (category 2 encoders) and “in which explosive atmospheres caused by gases, vapours, mists, or air/dust mixtures are unlikely to occur or, if they do occur, are


Aperçu Programmable draw-wire encoder, a first for market! de Lika Electronic
17/04/2015

Programmable draw-wire encoder, a first for market!

Lika Electronic introduces a new range of incremental and absolute draw-wire encoders with increased measuring lengths up to 5,000 mm (196.85”) and 10,000 mm (393.7”). Worthy of remark the first cable-pulling measuring system with integral programmable incremental encoder.


Aperçu All-round wheeled encoder for conveyor systems de Lika Electronic
03/03/2015

All-round wheeled encoder for conveyor systems

IR01 is the underbelt measuring system encompassing a double rubber wheel with integrated incremental encoder and the mounting support in the same package. Easy to install, it tracks displacements more precisely.


Aperçu SMP encoder for linear guideways de Lika Electronic
03/03/2015

SMP encoder for linear guideways

SMP is the magnetic encoder designed for feedback on linear guideways, carriages, slides, positioning tables and all applications that need the scale to be mounted laterally.


Aperçu Un codeur, 65.536 codeurs de Lika Electronic
09/02/2015

Un codeur, 65.536 codeurs

Les codeurs incrémentaux programmables IQ58/IP58 de Lika Electronic sont conçus expressément pour être polyvalents et adaptables aux exigences spécifiques de chaque utilisateur. Ils garantissent un paramétrage complet au moyen du PC et proposent une large gamme d'options de connexion mécaniques et électriques. Ils sont donc entièrement personnalisables et offrent une flexibilité absolue pour répondre aux besoins industriels les plus pointus.


Aperçu Best in price analogue encoder de Lika Electronic
13/11/2014

Best in price analogue encoder

With its quality feature set and the attractive price tag, MS40 series from Lika Electronic further grows adding the 4-20 mA and 0-10V analogue interface today.


Aperçu Tough for rough! de Lika Electronic
13/11/2014

Tough for rough!

MMK36 is the only multiturn absolute encoder with bearingless shaft in the market. Still it is capable of reliably and safely withstanding the most aggressive environmental conditions and ideally suited even for position measurements at speeds up to 4,000 RPM.


Aperçu SFP draw-wire encoders gain analogue outputs de Lika Electronic
08/10/2014

SFP draw-wire encoders gain analogue outputs

Lika Electronic is releasing new SFP series cable-pulling encoders that provide linear position feedback over distances from 300 mm / 11.8” to 2000 mm / 78.7” and analogue outputs now.


Aperçu SSI to Profibus IF55 gateway de Lika Electronic
08/10/2014

SSI to Profibus IF55 gateway

Connect your Lika SSI encoder to Profibus with the new IF55 gateway. IF55 gateway allows complete integration and full compliance with the Profibus-DP protocol.


Aperçu Change-over at your fingertips de Lika Electronic
17/09/2014

Change-over at your fingertips

LDT10 is the HMI touch panel specifically designed to easily interface and configure Lika RD rotary actuators, so auxiliary axes are more intuitive to operate and change-over operations become as fast as one touch.


Aperçu The bearingless solution for torque motors and heavy-duty applications de Lika Electronic
17/09/2014

The bearingless solution for torque motors and heavy-duty applications

SMRI from Lika Electronic is the miniature encoder intended for installation in dynamic and demanding rotary motion systems. It ensures safe and reliable operation even in harsh environments. A wide range of custom ring diameters and resolutions is available on request.


Aperçu Flat Design with Hollow Through Bore de Lika Electronic
17/09/2014

Flat Design with Hollow Through Bore

CH59 from Lika Electronic is the new incremental optical encoder featuring an extremely slim enclosure and high resolutions up to remarkable 204,800 PPR. Designed for electro-medical applications, analysis and laboratory equipment, motor testbeds.


Aperçu New IF55 converters, increased possibilities de Lika Electronic
17/09/2014

New IF55 converters, increased possibilities

Lika Electronic launches a new series of gateways to allow integration of SSI encoders into conventional fieldbuses or industrial Ethernet networks. Perfect for retrofitting and encoder installations where space is constricted. SSI to EtherCAT model released first.