IF52: SSI / RS-232 Serial to Parallel converter for absolute encoders and sensors

IF52: SSI / RS-232 Serial to Parallel converter for absolute encoders and sensors de Lika Electronic

Par: Lika Electronic  03/09/2012
Mots-clés : Capteurs, Encodeur, Codeurs

Lika Electronic strengthens the signal converters portfolio introducing the new SSI/RS-232 SERIAL-TO-PARALLEL IF52 unit. Lika offers a broad choice of affordable and complete converting solutions focused on easily integrating modern and outdated industrial applications while avoiding expensive replacements and saving both time and money. Discover IF- full range and the most recent additions at the address http://www.lika.it/eng/prodotti.php?ID=6. IF52 is the latest innovation in the series born to solve your signal conversion and modernization needs. It is compact and low-cost and is designed to convert SSI encoder data to either parallel output or serial RS-232 data format; yet it can accept also serial data from a RS-232 source and convert it to parallel output. It can be connected to all single-turn and multi-turn encoders and sensors fitted with 6- to 25-bit resolution standard SSI interface and either Binary or Gray code. The unit will then deliver data in parallel format and Binary, Gray or BCD code through the 25-bit interface with Push-Pull characteristics. Parallel outputs are protected against short circuit provided a 27 volts max voltage is applied. Basic configuration can be performed via DIL switches directly on the unit, while the full capabilities of the more advanced configuration are available via serial interface using the software tool supplied for free. In this way data source (SSI or RS-232 serial data) can be selected along with the parallel output characteristics (Binary, Gray or BCD code). Furthermore extended setting options enable to set up the baud rate (clock frequency between 100 Hz and 1 MHz) and the telegram interval time of the SSI interface to meet any cable run needs. Please note the IF52 unit is designed to operate in either Master mode (i.e. the clock signal is generated by the unit) or in Slave mode (i.e. the clock signal is generated by the remote Master device). As stated, IF52 converter is also equipped with a serial RS-232 interface (9-pin Sub-D connector) that allows both to convert SSI data to serial format and to interface the unit for powerful parametrization. Also RS-232 port baud rate and format are freely selectable. IF52 converter provides you with several advantages, among the others: the conversion of the position information into any engineering unit such as millimetres or inches; the ROUND LOOP function to replace the real encoder position with a repeating cycle count; the BIT BLANKING function for a tailored evaluation of the encoder information; the programmable LINEARISATION feature which allows the user both to correct precision errors of the sensor and to convert a linear motion to a non-linear data output (and vice versa); the HOLD input to “freeze” the parallel information; the DATA STABLE output for remote latch of the parallel data. IF52 converter comes in a compact and sturdy plastic housing with DIN rail mounting and can quickly snap onto a DIN rail with built-in DIN rail clips that require no additional brackets or supports. Electrical connection is through 12 screw terminals; unit accepts inputs from 5 to 27 volts. Power supply is 18-30 VDC.

Mots-clés : Capteur Absolu, Capteurs, Codeur absolu, Codeur absolu magnétique, Codeur Linéaire, Codeur magnétique, Codeur monotour, Codeur multitour, Codeur Optique, Codeur optique absolu, Codeurs, Codeurs Linéaires, Codeurs Optiques, Encodeur, Encodeurs, Interface parallèle, Interface sérielle, Système de mesure magnétique, Transducteur digital,

Autres produits et services de Lika Electronic

Aperçu Encoders for Industrial Robots, Motors and OEM applications de Lika Electronic

Encoders for Industrial Robots, Motors and OEM applications

At latest SPS IPC Drives exhibition in Nuremberg Lika Electronic especially focused on the range of encoders designed to be integrated into robotic systems as well as into motors and OEM applications. They are compact and modular and tailored to exactly meet the specific needs of the individual automation processes.

Aperçu Heavy-duty encoders for shipbuilding industry de Lika Electronic

Heavy-duty encoders for shipbuilding industry

Encoders for shipbuilding industry, marine installations and offshore facilities are born out of Lika's long-standing, solid experience in the field. They are designed to cope with extreme and high aggressive environmental conditions. Stainless steel enclosures and special surface treatments and sealings ensure safe protection against salt water and corrosion. They are rugged and can withstand heavy mechanical stresses, shocks and vibrations and large temperature fluctuations up to -40°C +100°C

Aperçu ATEX certified encoders de Lika Electronic

ATEX certified encoders

Lika Electronic has developed a comprehensive range of ATEX certified encoders: XC77 series, XAC77 series and XAC80 series. They are designed to cover a wide variety of critical applications in hazardous and harsh areas “in which explosive atmospheres caused by gases, vapours, mists or air/dust mixtures are likely to occur occasionally” (category 2 encoders) and “in which explosive atmospheres caused by gases, vapours, mists, or air/dust mixtures are unlikely to occur or, if they do occur, are

Aperçu Programmable draw-wire encoder, a first for market! de Lika Electronic

Programmable draw-wire encoder, a first for market!

Lika Electronic introduces a new range of incremental and absolute draw-wire encoders with increased measuring lengths up to 5,000 mm (196.85”) and 10,000 mm (393.7”). Worthy of remark the first cable-pulling measuring system with integral programmable incremental encoder.

Aperçu All-round wheeled encoder for conveyor systems de Lika Electronic

All-round wheeled encoder for conveyor systems

IR01 is the underbelt measuring system encompassing a double rubber wheel with integrated incremental encoder and the mounting support in the same package. Easy to install, it tracks displacements more precisely.

Aperçu SMP encoder for linear guideways de Lika Electronic

SMP encoder for linear guideways

SMP is the magnetic encoder designed for feedback on linear guideways, carriages, slides, positioning tables and all applications that need the scale to be mounted laterally.

Aperçu Un codeur, 65.536 codeurs de Lika Electronic

Un codeur, 65.536 codeurs

Les codeurs incrémentaux programmables IQ58/IP58 de Lika Electronic sont conçus expressément pour être polyvalents et adaptables aux exigences spécifiques de chaque utilisateur. Ils garantissent un paramétrage complet au moyen du PC et proposent une large gamme d'options de connexion mécaniques et électriques. Ils sont donc entièrement personnalisables et offrent une flexibilité absolue pour répondre aux besoins industriels les plus pointus.

Aperçu Best in price analogue encoder de Lika Electronic

Best in price analogue encoder

With its quality feature set and the attractive price tag, MS40 series from Lika Electronic further grows adding the 4-20 mA and 0-10V analogue interface today.

Aperçu Tough for rough! de Lika Electronic

Tough for rough!

MMK36 is the only multiturn absolute encoder with bearingless shaft in the market. Still it is capable of reliably and safely withstanding the most aggressive environmental conditions and ideally suited even for position measurements at speeds up to 4,000 RPM.

Aperçu SFP draw-wire encoders gain analogue outputs de Lika Electronic

SFP draw-wire encoders gain analogue outputs

Lika Electronic is releasing new SFP series cable-pulling encoders that provide linear position feedback over distances from 300 mm / 11.8” to 2000 mm / 78.7” and analogue outputs now.

Aperçu SSI to Profibus IF55 gateway de Lika Electronic

SSI to Profibus IF55 gateway

Connect your Lika SSI encoder to Profibus with the new IF55 gateway. IF55 gateway allows complete integration and full compliance with the Profibus-DP protocol.

Aperçu Change-over at your fingertips de Lika Electronic

Change-over at your fingertips

LDT10 is the HMI touch panel specifically designed to easily interface and configure Lika RD rotary actuators, so auxiliary axes are more intuitive to operate and change-over operations become as fast as one touch.

Aperçu The bearingless solution for torque motors and heavy-duty applications de Lika Electronic

The bearingless solution for torque motors and heavy-duty applications

SMRI from Lika Electronic is the miniature encoder intended for installation in dynamic and demanding rotary motion systems. It ensures safe and reliable operation even in harsh environments. A wide range of custom ring diameters and resolutions is available on request.

Aperçu Flat Design with Hollow Through Bore de Lika Electronic

Flat Design with Hollow Through Bore

CH59 from Lika Electronic is the new incremental optical encoder featuring an extremely slim enclosure and high resolutions up to remarkable 204,800 PPR. Designed for electro-medical applications, analysis and laboratory equipment, motor testbeds.

Aperçu New IF55 converters, increased possibilities de Lika Electronic

New IF55 converters, increased possibilities

Lika Electronic launches a new series of gateways to allow integration of SSI encoders into conventional fieldbuses or industrial Ethernet networks. Perfect for retrofitting and encoder installations where space is constricted. SSI to EtherCAT model released first.