IF10 UNIT: CONVERT, REPEAT, SPLIT, SWITCH, ALL IN ONE, AS YOU NEED

IF10 UNIT: CONVERT, REPEAT, SPLIT, SWITCH, ALL IN ONE, AS YOU NEED de Lika Electronic

Par: Lika Electronic  06/08/2012
Mots-clés : Capteurs, Encodeur, Codeurs

- Most IN/OUT incremental interfaces in a range of voltages; - High counting frequency range (1 MHz); - Auxiliary 5V output for encoder supply; - DIN rail mounting using clips; - Converter to integrate incompatible electronics; - Repeater for safe transmission over long distances; - Splitter to duplicate signals for different equipments; - Switcher to commutate encoder signals. IF10 is the multipurpose unit designed to convert, repeat, split and cross switch incremental encoder digital signals (and even signals delivered by proximity switches, photocells, etc.). It fits two independent inputs and two independent short-circuit-proof outputs. It can accept on the input side single channel (AB0) and quadrature (AB0, /AB0) encoder signals with either Line Driver (RS-422) format or TTL or HTL10-30V (Push-Pull) level. As stated, inputs 1 and 2 are independent, thus for instance they can accept position information from A, /A, B and /B channels of an RS-422 encoder and add the corresponding 0 index pulse as a Push-Pull signal from a remote photocell. Aside from the input level, outputs always provide AB0 and /AB0 signals in RS-422 format or TTL or HTL level. Push-Pull output level depends on the power supply voltage (+12÷+30VDC). IF10 boasts a slim and space-saving plastic housing with DIN rail mounting using clips. It further affords frontal status LEDs for power supply and signal presence. Cables are connected via parallel terminal blocks. In details, IF10 can be used as explained hereafter. IF10 is an encoder signal converter and repeater. Independent inputs 1 and 2 can accept HTL10-30V or TTL5V or RS-422 signals both with and without complementary signals. They can be converted into HTL10-30V or TTL5V or RS-422 levels and then output through independent outputs 1 and 2; or even regenerated to prevent quality degradation or loss of signals on long cable runs. Output signals always provide complementary signals. HTL output level depends on the power supply input; TTL and RS-422 is always 5V. IF10 can be used as an encoder signal splitter. Only input 1 is used. It can accept HTL10-30V or TTL5V or RS-422 signals both with and without complementary signals. Signals are split into both outputs 1 and 2. They supply HTL10-30V or TTL5V or RS-422 independent signals always fitted with inverted signals. Thus independent output signals with even different characteristics can be delivered to two distinct control equipments. HTL output level depends on the power supply input; TTL and RS-422 is always 5V. IF10 is an encoder cross switcher. Independent inputs 1 and 2 can accept HTL10-30V or TTL5V or RS-422 signals both with and without complementary signals. RS-422 format or TTL or HTL level output signals are sent to independent outputs 1 and 2 and can be cross switched according to needs using provided control signals. HTL output level depends on the power supply input; TTL and RS-422 is always 5V.

Mots-clés : Capteur incrémental, Capteurs, Codeur incrémental magnétique, Codeur Linéaire, Codeur magnétique, Codeur optique incrémental, Codeurs, Codeurs Linéaires, Codeurs Optiques, Encodeur, Encodeurs, Push-Pull, Transducteur digital,

Autres produits et services de Lika Electronic

Aperçu Encoders for Industrial Robots, Motors and OEM applications de Lika Electronic
05/12/2016

Encoders for Industrial Robots, Motors and OEM applications

At latest SPS IPC Drives exhibition in Nuremberg Lika Electronic especially focused on the range of encoders designed to be integrated into robotic systems as well as into motors and OEM applications. They are compact and modular and tailored to exactly meet the specific needs of the individual automation processes.


Aperçu Heavy-duty encoders for shipbuilding industry de Lika Electronic
21/10/2016

Heavy-duty encoders for shipbuilding industry

Encoders for shipbuilding industry, marine installations and offshore facilities are born out of Lika's long-standing, solid experience in the field. They are designed to cope with extreme and high aggressive environmental conditions. Stainless steel enclosures and special surface treatments and sealings ensure safe protection against salt water and corrosion. They are rugged and can withstand heavy mechanical stresses, shocks and vibrations and large temperature fluctuations up to -40°C +100°C


Aperçu ATEX certified encoders de Lika Electronic
21/10/2016

ATEX certified encoders

Lika Electronic has developed a comprehensive range of ATEX certified encoders: XC77 series, XAC77 series and XAC80 series. They are designed to cover a wide variety of critical applications in hazardous and harsh areas “in which explosive atmospheres caused by gases, vapours, mists or air/dust mixtures are likely to occur occasionally” (category 2 encoders) and “in which explosive atmospheres caused by gases, vapours, mists, or air/dust mixtures are unlikely to occur or, if they do occur, are


Aperçu Programmable draw-wire encoder, a first for market! de Lika Electronic
17/04/2015

Programmable draw-wire encoder, a first for market!

Lika Electronic introduces a new range of incremental and absolute draw-wire encoders with increased measuring lengths up to 5,000 mm (196.85”) and 10,000 mm (393.7”). Worthy of remark the first cable-pulling measuring system with integral programmable incremental encoder.


Aperçu All-round wheeled encoder for conveyor systems de Lika Electronic
03/03/2015

All-round wheeled encoder for conveyor systems

IR01 is the underbelt measuring system encompassing a double rubber wheel with integrated incremental encoder and the mounting support in the same package. Easy to install, it tracks displacements more precisely.


Aperçu SMP encoder for linear guideways de Lika Electronic
03/03/2015

SMP encoder for linear guideways

SMP is the magnetic encoder designed for feedback on linear guideways, carriages, slides, positioning tables and all applications that need the scale to be mounted laterally.


Aperçu Un codeur, 65.536 codeurs de Lika Electronic
09/02/2015

Un codeur, 65.536 codeurs

Les codeurs incrémentaux programmables IQ58/IP58 de Lika Electronic sont conçus expressément pour être polyvalents et adaptables aux exigences spécifiques de chaque utilisateur. Ils garantissent un paramétrage complet au moyen du PC et proposent une large gamme d'options de connexion mécaniques et électriques. Ils sont donc entièrement personnalisables et offrent une flexibilité absolue pour répondre aux besoins industriels les plus pointus.


Aperçu Best in price analogue encoder de Lika Electronic
13/11/2014

Best in price analogue encoder

With its quality feature set and the attractive price tag, MS40 series from Lika Electronic further grows adding the 4-20 mA and 0-10V analogue interface today.


Aperçu Tough for rough! de Lika Electronic
13/11/2014

Tough for rough!

MMK36 is the only multiturn absolute encoder with bearingless shaft in the market. Still it is capable of reliably and safely withstanding the most aggressive environmental conditions and ideally suited even for position measurements at speeds up to 4,000 RPM.


Aperçu SFP draw-wire encoders gain analogue outputs de Lika Electronic
08/10/2014

SFP draw-wire encoders gain analogue outputs

Lika Electronic is releasing new SFP series cable-pulling encoders that provide linear position feedback over distances from 300 mm / 11.8” to 2000 mm / 78.7” and analogue outputs now.


Aperçu SSI to Profibus IF55 gateway de Lika Electronic
08/10/2014

SSI to Profibus IF55 gateway

Connect your Lika SSI encoder to Profibus with the new IF55 gateway. IF55 gateway allows complete integration and full compliance with the Profibus-DP protocol.


Aperçu Change-over at your fingertips de Lika Electronic
17/09/2014

Change-over at your fingertips

LDT10 is the HMI touch panel specifically designed to easily interface and configure Lika RD rotary actuators, so auxiliary axes are more intuitive to operate and change-over operations become as fast as one touch.


Aperçu The bearingless solution for torque motors and heavy-duty applications de Lika Electronic
17/09/2014

The bearingless solution for torque motors and heavy-duty applications

SMRI from Lika Electronic is the miniature encoder intended for installation in dynamic and demanding rotary motion systems. It ensures safe and reliable operation even in harsh environments. A wide range of custom ring diameters and resolutions is available on request.


Aperçu Flat Design with Hollow Through Bore de Lika Electronic
17/09/2014

Flat Design with Hollow Through Bore

CH59 from Lika Electronic is the new incremental optical encoder featuring an extremely slim enclosure and high resolutions up to remarkable 204,800 PPR. Designed for electro-medical applications, analysis and laboratory equipment, motor testbeds.


Aperçu New IF55 converters, increased possibilities de Lika Electronic
17/09/2014

New IF55 converters, increased possibilities

Lika Electronic launches a new series of gateways to allow integration of SSI encoders into conventional fieldbuses or industrial Ethernet networks. Perfect for retrofitting and encoder installations where space is constricted. SSI to EtherCAT model released first.